Lowriders

G Funk · 07-14-2002, 02:04 AM

Got a bit of a problem with a friend's car, one of the motors on his pump is stuffed and needs replacing, but we are experiencing trouble getting the motor off the pump. Usually, you just undo 2 bolts, and that should be it, not in this case. Can somebody tell me if there could be another bolt inside the the pump, that could be holding it? (I believe they're Red's hydro's)... Your help would be appreciated...

07-14-2002, 03:58 AM

itsprobably just galded on there from time and heat...

DRLOWZ · 07-14-2002, 10:12 AM

I agree, David your just going to have to hammer the shit out of that thing, in probably got so hot that it mended with the block. It will come off, just keep at it.

Dennis

alarman · 07-14-2002, 03:38 PM

my old reds pumps only had 2 bolts it's probally just stuck so just work it a little it should come off

Unity_Jon · 07-15-2002, 07:26 AM

Use TWO levers (screwdrivers ?) opposite each other with equal pressure to seperate the motor from the block, if you try to pull one side then the other you'll never get them apart.

UCYI3WL · 07-15-2002, 12:02 PM

Arent Reds Hydros fun!! It used to stick on my Nissan all the time...Lightly tap the motor where it connects to the block...Should come right off with a little pressure after that...

OrangeCounty58 · 07-27-2002, 08:45 PM

the metal just expanded a bit and sealed real tight. just do as mentioned and get those muscles into it.

07-14-2002, 02:04 AM	#1 (permalink)
G Funk Registered User Join Date: Jun 2002 Location: Australia Posts: 35	12V Motor problem HELP Got a bit of a problem with a friend's car, one of the motors on his pump is stuffed and needs replacing, but we are experiencing trouble getting the motor off the pump. Usually, you just undo 2 bolts, and that should be it, not in this case. Can somebody tell me if there could be another bolt inside the the pump, that could be holding it? (I believe they're Red's hydro's)... Your help would be appreciated...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-14-2002, 03:58 AM	#2 (permalink)
UnitedRidaZ Posts: n/a	itsprobably just galded on there from time and heat...

07-14-2002, 10:12 AM	#3 (permalink)
DRLOWZ Administrator Join Date: Jun 2002 Location: Bardstown,Kentucky Posts: 4,938	I agree, David your just going to have to hammer the shit out of that thing, in probably got so hot that it mended with the block. It will come off, just keep at it. Dennis

07-14-2002, 03:38 PM	#4 (permalink)
alarman Registered User Join Date: Jul 2002 Location: kinston, n. c. Posts: 200	my old reds pumps only had 2 bolts it's probally just stuck so just work it a little it should come off

07-15-2002, 07:26 AM	#5 (permalink)
Unity_Jon Registered User Join Date: Jun 2002 Location: United Kingdom Posts: 240	Use TWO levers (screwdrivers ?) opposite each other with equal pressure to seperate the motor from the block, if you try to pull one side then the other you'll never get them apart.

07-15-2002, 12:02 PM	#6 (permalink)
UCYI3WL UnitedRidaz C.C. Join Date: Jun 2002 Location: Birmingham, AL Posts: 2,813	Arent Reds Hydros fun!! It used to stick on my Nissan all the time...Lightly tap the motor where it connects to the block...Should come right off with a little pressure after that...

07-27-2002, 08:45 PM	#7 (permalink)
OrangeCounty58 Registered User Join Date: Jul 2002 Location: Orange County Posts: 101	the metal just expanded a bit and sealed real tight. just do as mentioned and get those muscles into it.

Lowriders

12V Motor problem HELP

12V Motor problem HELP